• sns01
  • sns02
  • linkedin
Search

PriceList for Drilling Equipment Drawworks - Motor Model Description Of Design – LUQI

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

"Sincerity, Innovation, Rigorousness, and Efficiency" could be the persistent conception of our organization for your long-term to establish alongside one another with shoppers for mutual reciprocity and mutual benefit for Api 7k Oil Drilling Drawworks , Swivels Manufacturers , Oil Drilling , We intention at Ongoing system innovation, management innovation, elite innovation and market place innovation, give full play into the overall advantages, and frequently strengthen services excellent.
PriceList for Drilling Equipment Drawworks - Motor Model Description Of Design – LUQI Detail:

1. By-pass Assembly

It has two positions of by-pass and close. It is in by-pass position during trip operation, circulates mud fluid in the drill string into the annular space by-passing the idle motor, so that mo mud may spray out onto the platform during the trip operation. When mud flow rate and pressure reach the setting value, the valve stem moves down and closed the valve.

Meanwhile, mud stream flows through the motor, and converts the pressure energy into mechanical energy. As mud flow rate is too low, or mud pump stops, and as the created pressure is not enough to overcome spring force and static friction force, the spring presses the stem upward and by-pass is in open position. In general, the cross-over sub is used in deep well and large angle well horizontal well or hollow rotor selected.

dod06

2. Motor Assembly

It consists of stator and rotor. Stator is made by squeezing rubber sleeve on the wall of steel tube. There forms spiral structure with a certain geometric parameter. Rotor is a chrome-plated screw rod.

Stator and rotor matches with each other, to form spiral line and seal cavity through their guide rail difference. With rotor running in the stator, the seal cavity is moving along its axial direction, continuously forms and disappears to complete its energy conversion. This is the basic principle of down-hole motor.

Spiral seal line on rotor is divided into single end and multi-end (stator with one more end than rotor). The less ends the motor has, the higher speed and the lower torque are. The more ends it has, the lower speed and the higher torque are. The following figure shows the sectional profile of several typical motors.

dod07

3. Adjustable Bend Housing

In drilling the non-conventional wells such as directional wells, horizontal wells, and highly-deviated wells, downhole motor with adjustable bend housing which uses the new coupling design can be adjusted from 0°to 4°at 19 different angles. It overcomes the shortcomings of flat universal shaft such as the exposed surfaces are susceptible to erosion and short operational life.

dod08

4. Cardan Shaft Assembly/Universal Shaft Assembly

The function of cardan shaft is to convert planetary motion into fixed constant rotation of drive shaft, to transmit torque and speed from motor on the drive shaft, and to the bit. Cardan shaft mostly use flat shaft, but some are flexible shafts. Our flat type shaft used on our down-hole motor is made by linear cutting technology, so the cut has high parallelism, roughness. And it doesn’t damage metal chemical composition. Thus, it has longer running life and less mechanical loss.

Down-hole motor shall be disassembled as quickly as possible after use to examine cardan shaft. If it is found out that wear degree is over maintenance standard, relevant consumable components shall be changed promptly. If it is not, down-hole motor can not be running normally due to over run time of cardan shaft.

dod09

5. Drive Shaft Assembly

Drive shaft is to transmit motor rotary dynamic force onto the bit, meanwhile to withstand axial and radial load from drilling weight. We have two types of drive shafts, as follow:

i) Bit nozzle pressure loss is 7.0 Mpa, using hard alloy radial bearing and drive shaft assembly with thrust bearings.

ii) Bit nozzle pressure loss is 14.0 Mpa, using hard alloy radial bearing and PDC cutter flat thrust bearing. It has longer lasting life and higher bearing
capacity.

dod10

6. To suit different drilling request, we supply two kinds of stabilizers on the Bearing Assembly: Fixed Stabilizer and Replaceable Stabilizer.

7. Anti-Drop-Device

The safety catch sub is located between the power section and the dump valve (or crossover sub). It prevents leaving the rotor and internal motor components in the hole in the unlikely case of external connection failure in the motor string. It is generally used for extremely harsh drilling applications and where added precautions are required.

dod11


Product detail pictures:

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures

PriceList for Drilling Equipment Drawworks -
 Motor Model Description Of Design – LUQI detail pictures


Related Product Guide:
Design Theory of Stator and Rotor of PDM Based on Rack Gearing Principle
Directional well essential-Downhole Motor

We normally believe that one's character decides products' quality, the details decides products' high-quality ,while using the REALISTIC,EFFICIENT AND INNOVATIVE staff spirit for PriceList for Drilling Equipment Drawworks - Motor Model Description Of Design – LUQI , The product will supply to all over the world, such as: New Delhi , Namibia , Barcelona , Our products are widely recognized and trusted by users and can meet continuously changing of economic and social needs. We welcome new and old customers from all walks of life to contact us for future business relationships and mutual success!
  • We are long-term partners, there is no disappointment every time, we hope to maintain this friendship later!
    5 Stars By Dolores from Panama - 2018.05.13 17:00
    The factory workers have rich industry knowledge and operational experience, we learned a lot in working with them,we are extremely grateful that we can encount a good company has excellent wokers.
    5 Stars By Moira from Singapore - 2018.02.12 14:52
    Write your message here and send it to us